Pragmatic regularization of element-dependent effects in finite element simulations of ductile tensile failure initiation using fine meshes

For the evaluation of the structural response in accidental scenarios like ship collisions, the simulation of tensile failure initiation is inevitable. Here, one difficulty is that the process of failure initiation is a very local process, which cannot be simulated in its details at present due to the computing effort which would be required. However, there are various approaches how the failure initiation can be simplified and simulated in finite element models of large thin-walled structures. A short overview of these approaches is given. A pragmatic approach, which is suitable for relatively small elements for the simulation of failure initiation in uniaxial to biaxial stress states, is chosen within this paper for further investigations regarding the applicability for thin-walled steel structures. Exemplary simulations with solid and, in particular, shell elements are used to demonstrate how the effects of element size and other element properties can be considered in the simulation of failure initiation. The focus is also on imperfections that are relevant in simulations with small elements. For this purpose, an indentation experiment is simulated with different imperfections.     

准比例谐振控制算法在三相逆变电源中的应用研究

非线性负载会在三相车载逆变电源系统中引入谐波,损伤用电设备。为了降低逆变电源输出电压谐波含量,文章研究了基于准比例谐振控制算法的谐波抑制方法 ,主要抑制电源输出的5次和7次谐波。通过仿真模型和实物试验,测试了传统瞬时控制方法和准比例谐振控制方法的差别。结果表明,准比例谐振控制方法既能消除输出电压中的特定次谐波,又可满足系统动态响应性能和稳态精度要求,具有良好的谐波抑制效果。     

含初始变形船体加筋板有效宽度及剩余极限强度研究

为了评估舰船结构损伤后的剩余强度,对船体加筋板出现初始几何变形后,参与总纵强度的有效宽度和加筋板剩余极限强度进行研究。将加筋板受到垂直于平面压力后的变形,作为其初始几何变形,改变变形的方向和大小,利用有限元软件Ansys对加筋板结构进行线性和非线性分析。定义了板有效宽度计算方法,对不同变形方向和变形幅值时板的有效宽度和加筋板的极限强度进行对比分析,并拟合得到了计算板有效宽度和加筋板极限强度的经验公式。结果表明,初始几何变形会削弱加筋板结构的强度。在对损伤后船体结构强度进行分析和校核时,提出的经验公式可以直接用来计算板的有效宽度和加筋板的极限强度。     

秦岭马白山隧道新型紧急救援站结构型式研究北大核心CSCD

针对艰险山区高速铁路隧道的防灾救援难题,文章依托秦岭马白山隧道,提出了适合该隧道的新型紧急救援站结构型式,并利用FDS软件模拟隧道内纵向通风时列车着火后的烟气扩散,确定了规范中尚未给出的紧急救援站隔离区长度参数。结果表明:(1)秦岭马白山隧道新型紧急救援站结构型式应包括疏散区、隔离区以及待避救援区;(2)利用FDS数值模拟时,在不考虑纵向通风下,烟气沿下坡方向的扩散长度为295 m;考虑沿下坡方向通风时烟气最远扩散长度为980 m,建议隔离区长度设置为1000 m。     

编队飞行中基于危险区域的后机最优位置研究

编队飞行是实现民航绿色发展的重要措施之一。在前机尾涡危险区域分析的基础上，科学确定后机最优位置是编队飞行的关键。首先，以随机两阶段尾涡消散模型为基础，利用Hallock-Burnham涡模型和诱导滚转力矩系数模型分析后机诱导滚转力矩系数的演变规律。然后，基于设定的安全阈值，给出前机尾涡危险区域，并考虑飞行高度、速度和风对危险区域的影响。最后，基于后机不同位置处的燃油流量减少率，得出编队飞行中后机最优位置。研究结果表明：后机诱导滚转力矩系数随着前、后机之间横向距离的增加，呈先增后减再增的趋势；随纵向距离的增加，呈先缓慢减小后快速减小的趋势；高度越高、速度越小，诱导滚转力矩系数的峰值越高。飞行高度越高、速度越小，前机初始尾涡的危险区域越大；随着纵向距离的增加，危险区域不断减小，并随涡核的下沉不断下降。侧风使危险区域发生偏离，侧风越大，偏离程度越大。顺风会增加危险区域的纵向距离，顶风则与之相反。两架B737-800飞机在12000 m高度以0.78马赫数进行编队飞行时，前、后机纵向距离3000m处，无风情况下后机最优位置为横向距离30 m 或-30 m、垂直距离29 m，此时燃油流量减少率为7.01%。相较于无风，左侧风20 m·s -1 下，燃油流量减少率和垂直距离不变，横向距离增加；顺风20 m·s -1 下，燃油流量减少率增加，横向距离不变，垂直距离减少；顶风20 m·s -1 下，燃油流量减少率减小，横向距离不变，垂直距离增加。     

盾构隧道整体道床剥离病害规律研究北大核心CSCD

盾构隧道整体道床的剥离病害已严重影响地铁的安全运营。为研究整体道床剥离病害的规律,文章以国内某运营地铁线路为工程背景,建立整体道床-管片-注浆层数值模型进行分析研究。结果表明:列车轮组作用在道床一侧靠近伸缩缝位置时会引起较大的道床剥离变形,是最不利位置;列车荷载在振动作用下引起的剥离量远大于静载作用时的,且两者间存在函数关系;伸缩缝位置是最易发生剥离的区域,剥离首先发生在伸缩缝两侧边缘,随列车动载作用时间增加,剥离区域扩展至伸缩缝1.5 m范围内;注浆层刚度与接触面黏结强度均是影响剥离量的重要因素,提升注浆层刚度和道床-管片接触面的黏结强度可有效减少剥离量。     

考虑矿物各向异性的地聚物/集料界面静动态交互特征模拟

地聚物作为一种低碳环保、应用潜力广阔的无机结合料，其与不同表面构造集料的界面交互作用直接影响地聚物混凝土的力学性能和耐久性。充分考虑集料矿物晶向的各向异性，采用分子动力学模拟(Molecular Dynamics， MD)从原子分子层次的作用模式和强度分析，模拟了地聚物主要水化成分N-A-S-H、C-A-S-H和集料矿物化学成分SiO₂、CaCO₃不同晶面的静态界面相互作用，并采用单轴拉伸方法从纳米尺度下讨论了不同界面交互的动态力学行为。模拟结果表明：CaCO₃各晶面表现出比SiO₂更强的表面能和表面浸润性，并与C-A-S-H、N-A-S-H的界面相互作用势和拉伸应力更强，但CaCO₃晶面各向异性明显，性能稳定性不及SiO₂。地聚物与集料矿物的相互作用势主要由静电势提供，由于矿物界面静电作用及浸润特征，交互区水分子聚集，氢键作用明显，同时水分子与Ca²⁺、Na⁺进行配位形成水合离子，有助于离子在矿物表面迁移、沉淀与成核生长，增强界面空间位阻效应。在单轴拉伸模拟中，地聚物与集料矿物界面拉伸失效机制包括2个阶段：第1阶段(0 nm＜界面位移d＜0.15 nm)主要克服界面交互的静电作用，第2阶段(0.15 nm≤d≤0.3 nm)主要克服氢键作用。MD模拟有助于从分子尺度揭示地聚物与集料界面作用机制，为进一步研究地聚物混凝土材料优化、交互界面强化及损伤等提供了新方法和理论依据。     

Numerical simulation on truncated oval-nosed projectile penetrating into stiffened plate北大核心CSCD

[Objectives]In this paper, the numerical simulation method is used to study the anti-penetration performance and energy absorption mode of a stiffened plate, as well as the influence of different stiffened bars on the flight attitude of the projectile body.[Methods] Finite element software LS-DYNA is used to simulate the process of a truncated oval-nosed projectile penetrating a stiffened plate, and the results of the numerical simulation are compared with an experiment to verify the reliability of the numerical simulation method. The momentum method and mass equivalence method are used to predict the residual velocity of the projectile, and the applicability of different theoretical methods within different velocity ranges is compared. The deformation energy of different regions of the stiffened plate is then extracted to analyze the influence of the initial velocity of the projectile body on the energy absorption mode of the target plate. Finally, the structure of the stiffeners is changed and the influence of the relative position of the stiffeners on the penetration attitude of the projectile body is analyzed.[Results]The results show that the mass equivalence method is more accurate than the momentum method in predicting the residual velocity of the stiffened plate when the initial velocity of the projectile body is in the range of 300–900 m/s. The ratio of the deformation energy of the stiffened plate to the energy loss of the projectile body decreases with the increase of the initial velocity of the projectile body. The effect of a T-stiffened plate on trajectory is greater than that of a rectangular-stiffened plate.[Conclusions]The related calculation method and research results have certain reference value for research and engineering application surrounding the anti-penetration of stiffened plates. © 2023 Chinese Journal of Ship Research. All rights reserved.     

Simulation-based severe weather-induced container terminal economic loss estimation

Container terminals play a critical role in maritime supply chains. However, they show vulnerabilities to severe weather events due to the sea–land interface locations. Previous severe weather risk analysis focused more on larger assessment units, such as regions and cities. Limited studies assessed severe weather risks on a smaller scale of seaports. This paper aims to propose a severe weather-induced container terminal loss estimation framework. Based on a container terminal operation simulation model, monthly average loss and single event-induced loss are obtained by using historical hazard records and terminal operation records as model inputs. By studying the Port of Shenzhen as the case study, we find that the fog events in March lead to the longest monthly port downtime and the highest monthly severe weather-induced economic losses in the studied port. The monthly average loss is estimated to be 30 million USD, accounting for 20% of the intact income. The worst-case scenario is found to be a red-signal typhoon attack which results in nearly 20% decrease in the month’s income. The results provide useful references for various container terminal stakeholders in severe weather risk management.     

钢护筒与钢筋混凝土协同受力机理数值分析与模型验证

以果园二期桩基为原型,对6个钢护筒与钢筋混凝土短柱结构和2个钢管混凝土短柱进行轴压试验。基于ABAQUS有限元软件,以钢护筒厚度、配筋率、配箍率为参数进行分析。结果表明,钢护筒与钢筋混凝土短柱结构中,钢护筒与箍筋对核心混凝土均有约束作用,且双重约束效应明显,有效抑制混凝土裂缝开展,使结构具有更高的承载力、塑性和韧性。箍筋对混凝土的约束作用对钢护筒与钢筋混凝土短柱的承载力、塑性及延性性能影响显著,随着箍筋间距的减小,构件的承载力及延性性能有明显提高。